Apple power mac g5 manual download

Position the AirPort Extreme Card with the Apple logo facing up, insert the card into the card slot, and press it firmly into the connector. The AirPort Extreme Card slot is located underneath the sheet metal divider. Page Replacing The Battery Your computer has a 3. If your computer has intermittent problems starting up or random changes in its date and time settings, you may need to replace the battery.

Purchase a replacement battery from an Apple Authorized Reseller. Page 70 To replace the battery: Open your computer following the directions on page If a PCI card is installed next to the battery, remove the card. A plus sign is marked on or near the battery holder. If necessary, spread the tabs holding the battery so you can remove it.

If a dialog appears, click Cancel. Page 72 A file on the disc may be in use. Quit applications that are open, then try again. You have trouble using AirPort wireless communication. If you attempt to repair the display yourself, any damage you may cause to the display will not be covered by the limited warranty on your display. Contact an Apple Authorized Reseller or Service Provider for additional information about this or any other warranty question. The serial number of your Power Mac G5 is also on the configuration label, which is located inside the side panel, directly below the air deflector.

AGP 3. Page General Maintenance Always operate your computer in an upright position. In the unlikely event that coolant leaks in or from your computer, disconnect all electrical power to the computer and do not restart it. Do not wipe the lens with a paper towel or other abrasive surface. If you need to clean the lens, see an Apple Authorized Service Provider for a lens cleaner. Page 89 Forearms level or tilted slightly Lower back supported Thighs tilted slightly For more information about health, safety, and maintenance, go to the Apple ergonomic website at www.

Appendix B Safety, Maintenance, and Ergonomics 45—70 cm 18—28 in. Use this detailed guide to connect to the Internet. Page 92 Internet connection.


  • hex editor free mac os x?
  • adobe update management tool mac;
  • Apple Footer!
  • Unraid for mac.
  • APPLE POWER MAC G5 USER MANUAL Pdf Download.?
  • mvp baseball 2005 mac download.
  • Apple PowerMac Manual: powermac g5;

Appendix C Page Entering Your Information Make sure your modem is plugged into a phone line and you have the information from your ISP available. Click Network. Drag Internal Modem to the top of the Port Configurations list to make it the preferred, or primary, network interface. Click the Internal Modem icon, if necessary. Enter your dial-up telephone number, account name, and password, if necessary.

Click Connect. Internet Connect dials your ISP and establishes a connection. Choose Network Port Configurations from the Show pop-up menu. To set up a manual configuration: In Network preferences, choose Built-in Ethernet from the Show pop-up menu. Choose Manually from the Configure IPv4 pop-up menu.

Type the other information into the corresponding fields. Click Apply Now. Page Next, make sure your AirPort connection options are active in Network preferences. Drag Built-in Ethernet to the top of the Port Configurations list. See the service and support information that came with your Apple product. Page See the service and support information that came with your Apple product for instructions on how to contact Apple or an Apple Authorized Service Provider for assistance. If you do not disconnect your modem when it is All telecommunications devices are required to hold a Telepermit and be labelled accordingly with the approved Telepermit number to comply with the New Zealand telecommunications standards, ensuring the health and safety of the This manual is also suitable for: Power mac g5 early Power mac g5 late Comments to this Manuals Your Name:.

Enter text from picture:. Latest comments:. Print page 1 Print document pages. Cancel Delete. Sign in OR. For example, an 8x card installed in a 4x slot will operate as a 4x card. Refer to the following table for details. Install other PCI Express cards in the slots labeled 2, 3, and 4. Warning: When removing or installing a card, handle it only by the edges. Do not touch its connectors or any of the components on the card. Lift the card straight out from the connector to remove it, and insert it straight into the connector to install it.

Once the replacement card is installed, pull on it gently to check that it is properly connected. Remove the screw that mounts the card to the enclosure. If you are removing a video card, pull back the small locking clip at the front of the connector. Holding the card by the top corners, gently pull up the card and remove it from its expansion slot.

If you meet a lot of resistance, pull the card out. Check the connector and the slot for damage or obstructions, then try inserting the card again. If it resists and stays in place, and if its gold connectors are barely visible, the card is connected. Remove the two screws that mount the card to the enclosure.

Disconnect the Quadro FX cable from the card. Replacement Note: When replacing the Quadro FX card, position the card over the slot by carefully aligning the end of the card in the first slot in the PCI card guide and the two screw holes in the card fence with the first two PCI card screw holes in the enclosure. Then press down. Remove the Quadro FX card from the enclosure refer to preceding steps.

Locate the PCI card guide. Remove the two screws that mount the PCI card guide to the logic board. Slide the card guide up to release the two latches from the PCI divider, and remove the card guide from the enclosure. Disconnect the Quadro FX cable from the logic board and remove the cable from the enclosure. Tools No tools are required for this procedure. You may, however, find a flat-blade screwdriver useful in removing the battery from its holder. If necessary, carefully spread the two tabs holding the battery. Remove the battery from its holder.

Warning: Installing the battery incorrectly may cause an explosion. Use only the same type of battery or an equivalent recommended by the manufacturer of the original. Important: Batteries contain chemicals, some of which may be harmful to the environment. Please dispose of used batteries according to your local environmental laws and guidelines. This procedure includes steps for removing both the combo and runway cards. However, if you are replacing just the combo card, it is not necessary to remove the runway card from the enclosure.

Disconnect the combo card antennas from the clip on the side of the PCI divider. Disconnect the combo card from the runway card and lift up a short distance. Disconnect the two antenna cables from the card and remove the card from the enclosure. Note: The runway card is attached to the PCI divider by two black rivets. You must remove the rivets before disconnecting the card from the logic board.

Using a Xacto knife, pry up and remove the center plug of the first black rivet. Then pry up and remove the outer casing for the rivet. Repeat for the second rivet. Holding the runway card by its top edge, pull straight up to disconnect the card from the logic board. Preliminary Steps Before you begin, open the computer, lay it on its side with the access side facing up, and remove any inch graphics or PCI Express cards. Disconnect the speaker and fan cables from the logic board. Important: Be careful that the fan and speaker cables do not catch on the PCI divider as you lift the assembly.

Locate the ambient board connected to the logic board. Position your fingers on both sides of the board. Gently rock the board from side-to-side, pulling it straight up and out of the connector.

Apple - Support - Manuals

Locate the locking rivet that secures the processor heatsink cover to the PCI divider. Using a Xacto knife, pry up and remove the plug at the center of the locking rivet. Replacement Note: For Power Mac G5 Late Dual computers, you do not need to replace the rivet after you have replaced the heatsink cover. Extra rivets are available as part number Slide the cover to the left to unlatch the four metal latches under the cover.

Then lift the cover up and off the heatsink.

Apple Power Mac G5 Replacement Instructions Manual

Replacement Note: Place the notches in the underside of the cover directly over the four mounting pegs. Slide the cover toward the back of the computer and then press down firmly until you feel the cover lock into place. Tools The only tools required for this procedure are a Phillips 1 screwdriver and a flatblade screwdriver.

If you are replacing the rear exhaust fans with new fans, you will also need needlenose pliers. Disconnect the fan cable from the logic board. Note: Press the cable connector up toward the media shelf when disconnecting the cable. Press down on the two tabs on the top of the fan bracket to release the two latches. Lift the fan bracket and fans out of the enclosure. If you are replacing the fans on a Power Mac G5 Late Quad computer, use needlenose pliers to pull each fan off the four grommets that mount it to the bracket, and remove the fans and cable from the bracket.

Then install the replacement fans in the bracket, using the grommets included with the fans. Then rotate the fan back flush with the rear panel, making sure the two latches on the top of the bracket engage with the two slots on the top of the fan guide. Tools The only tools required for this procedure are a Phillips 1 screwdriver and Xacto knife. Before you can remove the card from the PCI divider, you must remove both rivets and disconnect the card from the logic board. You do not, however, have to remove the runway card or combo card from the enclosure. Using a Xacto knife, pry up and remove the center of the first black rivet that mounts the runway card to the PCI divider.

Remove the combo card antenna cables from the clip on the side of the PCI divider. Set the runway card with combo card attached to the side. There is no need to remove the runway card from the enclosure. Remove the processor heatsink cable from the clip on the PCI divider. Remove the three black PCI divider mounting screws. Replacement Note: Align the PCI divider on the logic board by placing it over the runway card connector. Be sure to replace the processor heatsink cable in the clip on the PCI divider. Tools The only tool required for this procedure is a short-handled or right-angle Phillips 2 screwdriver.

Disconnect the media bay fan cable from the logic board. Remove the two media bay fan mounting screws. Rotate the fan counterclockwise. Route the fan cable out through the opening in the media bay shelf and remove the fan from the media bay.


  • Related titles?
  • Apple Power Mac G5 Quad 2 5 Dual 2 0 2 3 Ghz Service Repair Manual | Airport | Macintosh.
  • mac mini server 2013 specs.
  • what does blocked plugin mean on my mac?

Then rotate the fan clockwise back into position. Lift the processor inlet frame off the processor. Remove the frame from the enclosure. Before installing the frame, apply the label to the frame as illustrated below. Tools The only tools required for this procedure are a long-handled 3 mm flathead hex driver and a long-handled 4 mm ballhead hex driver. Using a long-handled 3 mm flathead hex driver, remove the six processor mounting screws.

Four long screws mount the upper platform and two short screws mount the power supply terminal on the level below. Insert a long-handled 4 mm ballhead hex driver into the two holes on the top of the heatsink and loosen but do not remove the two captive screws. Warning: The heatsink and processor are one unit. Do not attempt to separate the heatsink from the processor. Tilting the processor could damage the heatsink seal. Lower the processor over the processor standoffs, and press down on the metal platform to make sure the processor is connected to the logic board.

Gently rock the heatsink until it feels seated. Insert a long-handled 4 mm ballhead hex driver into the two holes on the top of the heatsink and tighten the two captive screws. Using a long-handled 3 mm flathead hex driver, replace the two short screws that mount the power supply terminal. Using a long-handled 3 mm flathead hex driver, replace the four long processor mounting screws. Replace the processor inlet frame on the front of the heatsink. Replace the heatsink cover. Replace the rear exhaust fan assembly.

Replace all graphics and PCI Express cards. Replace the front inlet fan assembly. Important: Whenever you replace a processor with a new processor, you must run Apple Service Diagnostic once the computer is reassembled.

Troubleshooting

Note: There are two versions of the Quad processor. While your processor may look different from the one in the photos, the take-apart steps for both versions are similar. Any differences are called out in the procedure that follows. Remove the processor support bar cable from the clip on the PCI divider. For Version 2 of the processor, see steps Using a 3 mm flathead hex driver, loosen the four captive float plate screws. Do not remove the captive screws from their standoffs.

Using a 3 mm flathead hex driver, remove the four short screws that mount the two processor terminal assemblies. Using a 4 mm ballhead hex driver, loosen the four captive screws near the middle of the processor. For Version 1 of the processor, see steps Version 1 Processor Note: For replacement procedures for Version 2 of the processor, see steps Lower the processor over the processor standoffs. Press down on the middle bridge of the heatsink to make sure the processor is connected to the logic board. Using a 4 mm ballhead hex driver, tighten the four captive screws near the middle of the processor.

Using a 3 mm flathead hex driver, replace the four short screws that mount the two processor terminal assemblies. Using a 3 mm flathead hex driver, replace the six long processor mounting screws. Reconnect the processor support bar cable with the processor cable. Replace the processor support bar cable in the clip on the PCI divider. Replace the processor inlet frame assembly on the front of the heatsink. Important: If you are replacing the processor with a new processor, be sure to use the inlet frame included with the replacement processor.

Although the Power Mac G5 Late Dual support bar cable differs from the Quad cable it has two connectors rather than three , the take-apart procedure for all configurations is primarily the same. Remove the two mounting screws from the processor support bar. Disconnect the processor support bar cable from the logic board. Depress the two clips on either side of the front inlet fan connector and remove the connector from the support bar. Unclip the cable from the support bar and remove the cable from the bar.

Disconnect the power button cable from the front panel board. Remove the two front panel board mounting screws. Gently pull the board back from the front panel, tip the back of the board up so that it clears the DIMM slot ejectors, and remove the board from the enclosure. Make sure that the fingers of the shield enclose the board as shown in the illustration below. Replacement Note: When replacing the front panel board, align the ports on the board with the openings in the front panel board.

Then press the board firmly to the enclosure. Lay the computer so that the front panel is facing down. Remove the black rubber cap that covers the power button LED. Remove the metal activation ring that lies below the power button board. Disconnect the cables from the top and bottom edge of the logic board.

Using a Phillips 1 screwdriver, remove the three black logic board mounting screws. Move the cables and processor power terminal assemblies out of the way. Then carefully slide the logic board to the left to release it from the three mushroom-head standoffs. Tilt the logic board up and maneuver it out of the enclosure, making sure the ports clear the enclosure openings. Transfer the port EMI shield from the original logic board to the replacement logic board, making sure the shield is fully seated on the ports. Important: Before you install a replacement logic board, remove the protective clips and caps circled in the illustration below and transfer them to the logic board you are returning to Apple.

Do not remove the mylar sheet from the board. Temporarily tuck the top cables into the openings in the media shelf so that they are out of the way. Also tape or hold the bottom cables out of the way. Note: You may find a long strip of packing tape useful in securing the cables. Angle the logic board into the enclosure so that the port edge goes in first. Warning: Be careful not to catch the battery on the edge of the case as you lower the logic board into the enclosure. Also make sure the connector ends of the antenna cables are not caught under the board.

Position the logic board on the three mushroom-head standoffs, aligning the ports with the openings in the enclosure. Slide the board toward the rear of the computer so that the logic board locks onto the mushroom-head standoffs and the ports are fully seated in the back panel openings.

Replace the three logic board screws and six standoffs in the order indicated below. Important: There are two versions of the power supply, one with two processor power terminal assemblies and the other with just one processor power terminal assembly. In either case, make sure the rear standoffs are threaded through the power terminal rings before you insert the standoffs into the logic board. Replace the nine power supply bus bar screws. Reconnect all cables at the top and bottom edge of the logic board.

Replace the PCI divider. Replace the front panel board. Replace the PCI card guide. Replace the rear exhaust fan assembly and reconnect its cable to the logic board. Replace the processor support bar and reconnect the processor support bar cable to the logic board. Replace the processor.

Replace the processor inlet frame. Important: Whenever you replace a logic board with a new logic board, you must run Apple Service Diagnostic once the computer is reassembled. Note: The antenna cables are permanently attached to the antenna board. The cables and board are removed from the enclosure as a unit.

Remove the three screws on the interior antenna board cover. Note: This procedure will also release the exterior antenna board cover on the back panel. Using a flatblade screwdriver, pry up the interior antenna board cover and remove the cover from the enclosure. Remove the antenna board and cables from the enclosure. Replacement Note: Insert the antenna board into the slot in the exterior antenna board cover as illustrated.

Position the computer so the power supply is at the top. Using a Phillips 1 screwdriver, remove the two screws that secure the power supply top cover, and remove the cover from the enclosure. Note: On some power supply covers, a pad attached to the top of the cover hides the left screw. To access this screw, gently peel back the pad as illustrated. Using the Phillips screwdriver, remove the four power supply mounting screws on the bottom of the enclosure.

Slide the power supply toward the front of the computer. Tilt the bus-bar-tab edge of the power supply a short distance out of the bottom of the enclosure. Make sure that the bus bar tabs are released from the plastic runner on the enclosure. Rotate the power supply up and remove it from the enclosure. Replacement Note: Make sure the plastic trim ring is in place in the power receptacle before replacing the power supply in the enclosure.

Apple Powermac G5 Ressurection - Part 1

Then slide the power supply toward the back of the computer, making sure the power receptacle aligns with the opening in the back panel. Note: Make sure the power supply cables do not catch on the enclosure or under the power supply. Replacement Note: Be sure to replace the mushroom-head standoff after installing the power supply in the enclosure. Tools The only tool required for this procedure is a flatblade screwdriver.

A small mirror to use in locating the board is optional. Locate the air deflector sensor board inside the enclosure on the bottom right front corner of the frame. You may find a small mirror useful in seeing the board. Three generations of Power Mac G5 were released before it was discontinued as part of Apple's transition to Intel processors , making way for its replacement, the Mac Pro. The Mac Pro retained the G5's enclosure design for seven more years, making it among the longest-lived designs in Apple's history.

Officially launched as part of Steve Jobs ' keynote presentation at the Worldwide Developers Conference in June , the Power Mac G5 was introduced with three models, sharing the same physical case, but differing in features and performance. The physical case of the Power Mac G5 was very different and unusual compared to any other computer at that time.

Asd 3s138 download

Although somewhat larger than the G4 tower it replaced, the G5 tower had room inside for only one optical, and two hard drives. The supercomputer managed to become one of the top 5 supercomputers that year. The computer was soon dismantled and replaced with a new cluster made of an equal number of Xserve G5 rack-mounted servers, which also use the G5 chip running at 2.

According to IBM's Dr. John E. Kelly, "The goal of this partnership is for Apple and IBM to come together so that Apple customers get the best of both worlds, the tremendous creativity from Apple Computers and the tremendous technology from the IBM corporation. Each processor in the Power Mac G5 has two unidirectional bit pathways: one leading to the processor and the other from the processor.

The processor at the heart of the Power Mac G5 has a " superscalar , superpipelined" execution core that can handle up to in-flight instructions, and uses a bit , instruction SIMD unit AltiVec. All modern bit x86 processors since the Pentium Pro have the Physical Address Extension PAE feature, which permits them to use a bit physical memory address to address a maximum of 2 36 bytes 64 gigabytes of physical memory , while the PowerPC processor is capable of addressing 2 42 bytes 4 terabytes of physical memory and 2 64 bytes 16 exabytes of virtual memory.


  • Browse Manuals by Product?
  • dts audio code 8193 mac divx!
  • premiere pro 5.5 keygen mac.
  • Apple Power Mac G5 Quad 2 5 Dual 2 0 2 3 Ghz Service Repair Manual | Airport | Macintosh?

DP designates a dual-processor machine, SP designates a single-processor machine, and DC designates a dual-core-processor machine. Early versions of dual processor G5 computers have noise problems. The first one is ground loop -based interference, [6] which sometimes causes noise leaks into the analog audio outputs. This bug was fixed in Rev. The second noise problem came from the 'chirping' sound, which can be triggered by fluctuations in power draw. This noise problem was not fixed until the dual core generation of G5s was produced, however it did not affect the "Late " model at least there have never been any reports.

The power draw fluctuation was later attributed to the lack of power management features in the single-core processors. Although the noise problems did not prevent the affected computers from working, they were problematic for audio professionals and enthusiasts, especially for the liquid-cooled models, which had been expressly designed as mechanically quiet for discerning listeners. A common problem amongst single processor G5s was that the plate of metal soldered to the Logic Board connecting all eight of the RAM slots would, over time, expand and contract in such a way that the computer could not boot properly, as it would not detect any RAM.

The only way known to fix this problem is for someone to re-solder the plate themselves or expose the other side of the Logic Board to heat from a heat gun. The latter of these two options is far easier, as to access the plate of metal one would have to completely remove the Logic Board from the computer, whereas all one has to do to expose the other side is remove a fan.

All 2. This was a bold step for Apple, and should have allowed the use of very fast processors, giving Apple an advantage in both the performance and reliability race, but the system turned out to be subject to coolant leakage. While leakage was sometimes detectable by drops of green coolant in or beneath the machine, in many [ vague ] machines the seepage is so slight that it was almost impossible to detect without dismantling the entire computer.